SPOON HEAD COVER [RED] JW5

S07A, LEB. It is a red red cover that was particular about the color of an equivalent type R, the texture.

SPOON HEAD COVER [YELLOW] JW5

S07A. It is a red red cover that was particular about the color of an equivalent type R, the texture.

SPOON ENGINE COVER [RED] JW5

S07A, It is a red red cover that was particular about the color of an equivalent type R, the texture.

SPOON ENGINE COVER [YELLOW] JW5

S07A, It is a red red cover that was particular about the color of an equivalent type R, the texture.

SPOON THERMOSTAT [B16B] JW5

Spoon Thermostat lowers the actuation point by ~10℃ over the OEM thermostat to resist heat exchange.
Sub-zero / Extreme Winter conditions may require block-plate on Radiator to reach operating temperature.
OEM Thermostat opens at 80 ℃ fully open 90 ℃
SPOON Thermostat opens at 68 ℃ fully open 81 ℃

spoon OIL FILLER CAP

Extreme heat and engine vibration in Race Car can cause the OEM Plastic Cap to shake loose or even crack.
Spoon Oil Filler Cap made from High-Grade Aluminium, Expands at the same rate as your (Aluminium) Valve Cover, also has special rubber seal designed to reduce vibration transfer and hold cap in place.

seeker ULTRA-LIGHT OIL FILLER CAP [RED / BLUE / BLACK / GOLD / SILVER]

The aluminum oil filler cap is subjected to a lightening to the limit while sufficient strength has been achieved ultra-lightweight (individual weight ~60g). In addition, since we have adopted a good shape of Gakari finger is very easy to open and close the cap. One part of the vehicle such as FD2 you might shaft if fitted with a front tower bar outside is a difficult opening and closing of many filler cap those of layout through the just above the filler cap, but a round bar or the like to the filler cap lightening hole It can be relatively easily opened and closed by plug. Functional design that was obtained as a result of pursuing such utility is ideal for dress-up of the engine room.
WEIGHT: ~60g
AVAILABLE IN 5 COLOURS: ■Red ■Blue ■Black ■Gold ■Silver

SPOON MAGNETIC DRAIN BOLT, ENGINE

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Engine Drain Bolt sold individually.

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

SPOON RACING PLUG # 24 [3PCE]

For Circuit or Street use, Spoon Racing Plugs are optimesed for performance Honda engines.
As the Combusion Chamber heat value increases, the plugs have a better ability to cool down faster. (NGK8 number is equivalent.)

SPOON RESERVOIR TANK COVER SET [SOX] *NEW*

The last thing you want to do at the circuit is lose traction thanks to someone having dropped fluids on to the track surface, let alone drop your own fluids and contribute to the problem - Spoon Reservoir Covers slide over your Brake Fluid Reservoir and Clutch Fluid Reservoir (etc.) and are designed to catch any fluids that may be spilled under high lateral-G driving at the circuit. Also helps prevent damage to engine-bay paintwork from spillage of Fluids.
25% Cotton 75% Polyester. 1PCE.

SEEKER RESERVOIR TANK COVER SET [SOX]

Fire Retardant Material. It is a safe reservoir tank cover that was manufactured in the flame-retardant material. Brake and clutch, and by using covered the reservoir tank of power steering fluid, to keep the quickly absorbed engine room boiling over of fluid to clean. The color is also the identity of the SEEKER "SEEKER orange".

SPOON THERMO STAT  JW5

Spoon Thermostat lowers the actuation point by ~10℃ over the OEM thermostat to resist heat exchange.
Sub-zero / Extreme Winter conditions may require block-plate on Radiator to reach operating temperature.
OEM Thermostat opens at 80 ℃ fully open 90 ℃
SPOON Thermostat opens at 68 ℃ fully open 81 ℃

SPOON VENTULI BIG THROTTLE BODY [L15B] JW5

Spoon repeated the test review of a conventional throttle body, we have developed a Venturi Big throttle body as a product obtained a higher effect. The product is characterized by increasing the charging efficiency than the throttle body inner surface as venturi shape, also the inner surface roughness at the same time to feature a diamond-cutting in order to mirror-finished, it was to reduce the inhalation resistance to the limit. In addition to adopting the large-diameter butterfly, butterfly adopts an elliptical shape in the oblique section, durability is to ensure genuine equal.

SPOON VENTULI BIG THROTTLE BODY [NTS EXCHANGE SERVICE] JW5

Spoon repeated the test review of a conventional throttle body, we have developed a Venturi Big throttle body as a product obtained a higher effect. The product is characterized by increasing the charging efficiency than the throttle body inner surface as venturi shape, also the inner surface roughness at the same time to feature a diamond-cutting in order to mirror-finished, it was to reduce the inhalation resistance to the limit. In addition to adopting the large-diameter butterfly, butterfly adopts an elliptical shape in the oblique section, durability is to ensure genuine equal.

SPOON N1 MUFFLER KIT [TAIL SILENCER] JW5

In spoon, we have advanced development in all running stages to reach the higher sports performance of S660.
Among them, the exhaust system has been repeatedly tested in accordance with various engine specifications.
Although the S07A engine is 660 cc, while it is normal, it exerts sufficient exercise performance, but optimization of exhaust efficiency has become essential in order to apply ECU tune such as boost up and further advance the power up.
To optimize torque and power from normal vehicle to ECU tune vehicle, by making the center pipe 50 Φ and the main pipe 60 Φ different-diameter megaphone structure, by optimizing the layout, it is possible to achieve low torque without sacrificing Improved output in the high speed range.

We used 1.2 mm thick SUS 436 pipe and finished it lightweight while securing sufficient strength.
The finisher adopted 65 Φ 1 pull out which is also a symbol of the SPOON N 1 muffler, making it compatible with safety standards and fine N 1 sound.

Remarks & special note
Conformity to safety standards
■ Proximity exhaust noise
MT: 93 db
CVT: 90 db
■ Weight
5.3 kg (STD: 6.0 kg)

SPOON SUB SILENCER [N1] JW5

Sub Silencer for use with 65mm tip N1 Systems. -5dB reduction.

SES Muffler KIT for S660 "TRIDENT" JW5

"High power and high durability"
By optimizing the main pipe diameter and the internal structure of the silencer, we pursued a power feeling like penetrating the high rotation side without sacrificing low and medium speed torque. 
We also use wool that plays a role of muffling etc. with less aging. 

SOUND TUNING
special layout & structure main volume, the sound range which the driver feels easy to sense while the volume is within the safety standard conformity. 
RESULTS
The muffler corresponding to the vehicle inspection also realized a sensory sound that is not complaining and a sound quality that is unparalleled. 
I pridefully believe that it is the result of huge time spent repeatedly testing & error repeatedly. This product embodies 
DESIGN
"design determines function" is this product. 
The finisher adopted a polish curl tail with a sense of quality. 
As a result, we gained a specialty full of looks reminiscent of the concept model. 
LAYOUT
Because of the structure not suitable for mass production, although it costs only production cost, we pursued sensual exhaust notes with our own layout.

■ Material Stainless 
■ main pipe Diameter 42Φ → 50Φ → 42Φ × 3 
■ Center pipe diameter 42Φ 
■ Tip diameter 60Φ × 3 (polished curl tail) 
■ Safety standard compliant product (pre-certified acquired)
■ A special center pipe (42 Φ) behind the catalyst is attached. 

SPOON MAGNETIC DRAIN BOLT, TRANSMISSION

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Transmission Drain Bolt sold individually.

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

SPOON CLUTCH SLAVE HOSE JW5

Standard hydraullic lines use Rubber hose which is prone to flexing, ballooning and even splitting. Spoon Clutch Slave Hose uses high-strength Stainless Steel Braided Hose that has also been internally Teflon Coated resulting in reliable clutch operation.

SPOON CLUTCH DAMPER LESS HOSE JW5

Clutch delay damper is mounted on the original clutch line of S660 like the image.
This is a mechanism for protecting the driving system of missions, clutches etc. adopted in recent manual cars, but on the
contrary, direct clutch feel is damaged in sports driving.

Therefore, this delay mechanism was removed, and a mesh hose which made direct connection was made.
For those who are primarily in sports driving, we recommend using this hose and CLUTCH SLAVE HOSE together.

SEEKER SUPER SHIFT COLLAR [6MT] JW5

SPOON PREOGRESSIVE SPRING JW5

Since S660 has already been set low in STD, lowering down more than necessary will sacrifice stroke.

Therefore, at SPOON, we developed a lowdown spring that does not sacrifice the stroke and further improves the high turning ability of S660 within the scope of safety standard compliance.

Cornering performance and straight running stability are improving, but by setting the thrust up feeling in a mild direction, you can enjoy a wide range from town riding to winding and sports driving.

SPOON FULL SPEC DAMPER KIT JW5

SPOON advocated "3S Suspension" is the

■ riding comfortable even in town riding by making the starting area at the moment when the suspension sinks soft.
■ Improve direct load transfer and straight running stability by eliminating sliding resistance and making it smooth in the intermediate area.
■ In the vicinity of the bottom, it is tough and strong attenuation characteristics make it possible to achieve high durability even in extreme areas such as high G cornering and riding on curbstones.

However, in order to make use of this ideal suspension, it was necessary to first build an ideal body.
In the process of developing S660, we first developed rigid parts such as "STIFF PLATE series", "Rigid color", etc., we made the whole body rigid body and made the basis for full-scale development of the suspension.
This is the balanced total setting SPOON aims for.

In every stage including town riding, winding, circuit, etc., we designed and tested repeatedly in order to produce a safe, fun and fast damper kit at a high level, setting based on huge data, making an ideal car height adjustment kit Completed.

Both front and rear are equipped with a camber adjustment type Pilo upper mount, making it possible to adjust to the camber value according to the traveling stage, and it is also possible to cope with the tire fender line protrusion due to the big caliper installation.
We adopted Minebea (NMB) pillow ball which enables smooth and direct driving feel, realizing high durability.

We also secured enough rebound strokes and attached helper springs both front and rear to realize an ideal "spring feeling".
A wide range of settings such as lowdown setting at the circuit and street use are possible.

SPOON STABILIZER SET [FRONT] JW5

SPOON has been pursuing the suspension total setting in order to further improve the high exercise performance of S660 in a more balanced manner, but we will start selling the stabilizer as the first step.
We have tested the roll stiffness at various stages such as circuit, winding, town ride and adopt the optimum rate so far. By exchanging in front and rear sets, you can demonstrate high cornering performance with good balance.
We can greatly improve turning performance and straight running stability without sacrificing ride comfort, so we recommend you to recommend it for users who are not satisfied with a genuine damper.

■Hollow 22φ (210% genuine ratio) original 19.1φ
■exclusive holder bush included

SPOON STABILIZER SET [REAR] JW5

SPOON has been pursuing the suspension total setting in order to further improve the high exercise performance of S660 in a more balanced manner, but we will start selling the stabilizer as the first step.
We have tested the roll stiffness at various stages such as circuit, winding, town ride and adopt the optimum rate so far. By exchanging in front and rear sets, you can demonstrate high cornering performance with good balance.
We can greatly improve turning performance and straight running stability without sacrificing ride comfort, so we recommend you to recommend it for users who are not satisfied with a genuine damper.

■Hollow 15φ (200% ~ 220% genuine ratio) Original 11 φ
■2 step adjustment
■exclusive holder Bush included

STEERING STIFF PLATE KIT JW5

SPOON achieved high motor performance by developing and installing STIFF PLATE FRONT to improve the ground feeling and handling stability of S660 front section.
However, while pursuing the development of the car body, we are pursuing a higher level of steering stability in order to improve situations where we are constantly forced to correct from the "insufficient rigidity" and "unreliability" transmitted from the steering wheel, investigating cause and development test I piled up.

The part that was causing this was the fastening part of the steering gear box.
Normally, the steering gearbox is tightened firmly with four or more bolts in the subframe.
However, S660 was fastened with only two bolts, and there was play in the bolt hole of the fastening part, so twisting always occurred, and slight modification was necessary.
We increased the part to which the body and the steering gearbox are fastened and aimed at a structure with high rigidity that the body and the gearbox can receive even for large inputs.

Like the STIFF PLATE FRONT, the plate was designed exclusively by 3D CAD, and the 1.6 mm thick JSC 780 super high tension material was molded with the 800 t hydraulic press.
In addition, we made exclusive color with the same principle as the rigid color in the gap of fastening bolt part.

By raising the fastening strength of the steering gear box itself, it was possible to realize a direct, moist and superior steering feel.
Installation can be installed without any processing.

RIGID COLLAR [FRONT + REAR SET] JW5

SPOON FULL-MONOBLOCK CALIPER SET JW5

The biggest feature of this "FULL Monoblock Caliper" is its capless design, developed without any compromise in all its structure, performance and durability. Capless Full Mono Body is manufactured with "Angle head processing machine". By adopting this construction method, it became possible to reduce rubber parts, the liquid loss was reduced, the design of a caliper with high rigidity and light weight became possible.
Adoption of pad spring reduces rattle sound, adopting large diameter dust boot for ultra-thin piston satisfies the requested specifications even in street or circuit use.

Because the S660 STD brake disc adopts solid discs, it is inevitable that the brake temperature will rise excessively in sports driving even though it is a mini car with a light weight.
Therefore, we have newly developed a dedicated ventilated disk to fully demonstrate the performance of S660 FULL monocoque calipers.
By adopting an ideal ventilator with a disk diameter of 260 Φ and a thickness of 17 mm, we succeeded in dramatically improving brake cooling efficiency in sports driving and sustaining a stable brake feel.
Front brake pad is designed exclusively for full monocoque, we adopt the corresponding friction material from street to circuit, special shim is attached.

Remarks & special note
For S660 FULL MONOCOQUE CALIPER KIT requires the following three parts.

① Product name: BRAKE ROTOR 【Front】 JW5 For MONOCOQUE
Item No .: 45251 - JW 5 - 000
Price: 19,000 yen / 1 piece (excluding tax)
Required Quantity: 2 Sheets
② Product Name: BRAKE PAD 【Front】 JW 5 For MONOCOQUE
Item Number : 45022 - MJW - 000
List price: 22,000 yen (excluding tax)
③ Product name: BRAKE HOSE SET JW 5
Item No .: 01460 - JW 5 - 000
List price: 36,000 yen (excluding tax)

Caution) Make full use of the performance of FULL MONOCOQUE CALIPER Because it is designed exclusively for all, you can not use genuine brake discs, pads, hoses.

SPOON BRAKE ROTOR, FRONT [VENTILATED] JW5 (MONOCOCQUE CALIPER)

Because the S660 STD brake disc adopts solid discs, it is inevitable that the brake temperature will rise excessively in sports driving even though it is a mini car with a light weight.
Therefore, we have newly developed a dedicated ventilated disk to fully demonstrate the performance of S660 FULL monocoque calipers.
By adopting an ideal ventilator with a disk diameter of 260 Φ and a thickness of 17 mm, we succeeded in dramatically improving brake cooling efficiency in sports driving and sustaining a stable brake feel.

■ For S660 FULL MONOCOQUE CALIPER KIT This brake disc is specially designed.
■ Can not be used for genuine caliper.

SPOON BRAKE PAD, FRONTJW5 (MONOCOCQUE CALIPER)

This brake pad is specially designed for full monocoque for S660, and we adopt corresponding friction material from street to circuit.

■ For S660 FULL MONOCOQUE CALIPER KIT is a brake pad for exclusive use.
■ Can not be used for genuine caliper.

SPOON BRAKE PAD, REAR JW5 (STANDARD REAR CALIPER)

It is a rear pad made by pursuing the optimum front and rear brake balance for those who are wearing a full monocoque calipers and running mainly on the circuit.

■For genuine rear caliper

SPOON BRAKE HOSE SET JW5

A combination of low expansion coefficient No. 3 Teflon tube and stain mesh covering it produces direct brake touch and feel. Fitting is made of high strength steel.

■ When installing FULL MONOCOQUE CALIPER SET for S660, it is necessary to install this brake hose at the same time. (It is designed to be longer than genuine in order to cope with large brake enlargement.)

SPOON WHEEL NUT [BLUE] [SET OF 20]

M12 x 1.5 pitch - perfect for Honda.
■ Set of 20.
■ 60° Taper.
■ SPOON: 21.13g
■ HONDA: 31.65g

SPOON WHEEL NUT [RED] [SET OF 20]

M12 x 1.5 pitch - perfect for Honda.
■ Set of 20.
■ 60° Taper.
■ SPOON: 21.13g
■ HONDA: 31.65g

SPOON STRIPE [S660] *NEW* JW5

Spoon Stripe was released in 2015 as a sleek and stylish visual enhancment to your Honda.
Each set is specifically tailored for the vehicle and precision die-cut for ease of installation.
Utilizing the Type One orange colour, the Spoon Stripe adds a sporty look to the profile of your car.

SPOON WINDSHIELD BANNER

Spoon Windshield Banner is a functional and stylish upgrade. For fitment of Roll-Cage, the Sun-Visors must be removed for cage-clearance. The Spoon Banner replaces the function of the Window visors and can be trimmed to suit individual vehicle or personal requirments. Also weight saving through removal of window visors is a benefit.
Width: 185 x Height: 1450mm.

INSTALLATION TIPS:
- Wash car normally.
- Clean windscreen with Wax/Grease Remover.
- ISO Alcohol Wipe. - mix 1 droplet detergent with 2/3 Water 1/3 methylated spirits into Spray squirter.
- Squirt glass under banner. - Position Banner.
- Squeegee Water and Bubbles out.
- Trim edges with blade.
- Leave to dry in sun 1 Hour.

SW388 [15x6.5" +45 4X100] JW5 *NEW*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ ~4.3KG Per Wheel
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint
■ MADE IN JAPAN by Taneisya
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts
■ Centre cap sold separately
■ Clears Spoon Twin-Block Calipers without need for Spacer !
■ AVAILABLE NOW (June 2018)

SW388 [15x6.5" +35 4X100] EG6, EK4, DC2 *NEW*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ ~4.3KG Per Wheel
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint
■ MADE IN JAPAN by Taneisya
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts
■ Centre cap sold separately
■ Clears Spoon Twin-Block Calipers without need for Spacer !
■ AVAILABLE NOW (June 2018)

SW388 [15x8" +35 4X100] EF9, EG6, EK4, EM1, EJ8 *NEW RELEASE*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ ~5,24KG Per Wheel
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint
■ MADE IN JAPAN by Taneisya
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts
■ Centre cap sold separately
■ Clears Spoon Twin-Block Calipers without need for Spacer !
■ PRE-ORDERS NOW (ETA Late August 2019)

SW388 [16X7.5" +30 4X100] EG6, EK4, EM1, EJ8, GE8, GK5 *NEW RELEASE*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ ~X.XKG Per Wheel (TO BE CONFIRMED)
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint
■ MADE IN JAPAN by Taneisya
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts
■ Centre cap sold separately.
■ Clears Spoon Twin-Block Calipers without need for Spacer !
■ PRE-ORDERS NOW (ETA Late September 2019)

CENTER-CAP [SW388] ALL *NEW*

Spoon Sports Centre Cap for use with SW388 wheels.

■ Features Spoon Sports Logo
■ Center Bore 67mm
■ AVAILABLE NOW (February 2018)

STICKER 01 / YELLOW [SPOKE DECAL FOR SW388] ALL *NEW*

Genuine Spoon Sports spoke decal (Yellow).

■ AVAILABLE NOW (November 2018)

SPOON CRO-MO WHEEL NUT M12 [BLACK] EF9, EG6, EK9, EP3, FN2, FD2, FK5, FK7, FC1, FC2, DC2, DC5, AP1, AP2, GD3, GE8, GK5, ZF1, NA1*NEW RELEASE*

Spoon has developed new motorsport-spec CRO-MO WHEEL NUTS !! Of course they are Black to match your new SW388's, featuring the Spoon Logo and are now open-ended to suit extended Hub Bolts. Made in Japan from super-strong (yet lightweight) Chromium Molybdenum Steel, available in M12 x 1.5 pitch.

■ Set of 16 (16 PCE)
■ M12 x 1.5 pitch - perfect for Honda
■ 60° Taper / for Aftermarket Wheels
■ Released April 2019

SPOON BLUE WIDE DOOR MIRROR *NEW* JW5

Spoon Door Mirrors install over the existing standard wing mirrors - featuring 900R Curvature for increased field of view with low-distortion.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.

SPOON BLUE WIDE REAR VIEW MIRROR JW5

Spoon Mirrors install over the existing standard mirror featuring 14000R Curvature for increased field of view with low-distortion - Basically the same field of view as a 'Broadway' mirror with just the small compact size of the standard mirror body.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.

SPOON STEERING WHEEL [340mm]

Spoon Steering Wheel is manufactured by Momo Italy utilising an unique rim contour and 340mmm diameter specifically designed for maximum grip under race conditions - especially suited for FF vehicles with extreme 'kick-back'. Covered in the highest quality Itallian leather with Red-stitching.
■ Includes Spoon Horn Button (not sold separately).

SEEKER RACING SPEC STEERING WHEEL [325mm]

It is Kodawari of the steering wheel in pursuit of the sport driving, including race, and the like. 
The high rigidity and a 6061 aluminum alloy 5t with excellent corrosion resistance using the base frame epidermis was arrogance luxury smooth leather. (Using a punching leather to 9 o'clock, 3 o'clock in order to improve the familiar). Grip has adopted a finger Gakari good shape a slightly thick as can be driving and disconnect the power.  Stitch of the portion of force is applied does not have a worry that leather may come off even if I use it for many years I have been put in a cross-shaped. 
In addition to place a well-balanced logo and the top mark and our slogan to several places body finished in a stylish design. 
"R-SPIRIT" horn button of the dedicated will be attached. 
■ specification steering outer diameter: 325mm Frame: 6061 aluminum alloy 5t Stitch: Red color of the cross-stitch epidermis: Luxury Black smooth leather (partially use the punching leather) Embroidery: Top on the surface 6 o'clock SEEKER logo, at 12 o'clock mark, embroidery our slogan on the back 12 o'clockhorn: dedicated "R-SPIRIT" horn button included

SPOON STEERING BOSS [SRS DELETE] JW5

Spoon Steering Boss Kits are die-cast aluminium units designed for minimal weight and maximum strength.
Suitable for use with Spoon, Momo and Nardi wheels.
■ Includes SRS Delete Harness to eliminate the Airbag Warning Light.
■ Includes Steering Wheel Bolts (Allen style).

SPOON CARBON BUCKET SEAT [V2] *COMING SOON*

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.
■ Revised design to meet new Japanese safety standards (in development)
■ Pre-Orders JAN2019 - Production ETA April 2019

SPOON CARBON BUCKET SEAT [V1] *DISCONTINUED*

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.
■ Weight ~5.7Kg.
■ Discontinued 2018

SPOON ALUMINIuM SIDE STAY [FOR SPOON CARBON BUCKET SEAT]

Spoon Seat Bracket for use with Spoon Carbon Bucket Seats (Side-Mount).

■ Side-Mount Seat Bracket for use with Spoon Carbon Racing Bucket Seat.
■ For use with Seeker / Bride or Recaro Rails without side stay - for example Type-RO,RB. Drill Rail and fix with bolt.
■Includes Mounting hardware.

SEEKER x BRIDE FULL BUCKET SEAT [FRP]

It is a full bucket seat of the collaboration model of the BRIDE boasts a high rigidity and excellent hold of. The underlying shell has adopted the VIOS3 with the most matches easily seat position as much as possible down easy structure in Japanese type (Low MAX).
Shoulder support is somewhat smallish because, wearing indoor space to narrow a S2000 is also available.
This collaboration model inherits the design of the predecessor full bucket seat that had gotten popular, adopt a skin fabric red and black two-tone specification.
The BRIDE sheet somewhat strong competition image by the headrest further subjected to a dedicated logo embroidery to add a bright red stitch performance is intact, we have succeeded in that to be transformed into optimal fashionable to street youth It was.
BRIDE-made seat back protector in this product (black) is standard equipment.
Seat rail (sold separately) is a vehicle inspection also safe because it becomes a security standard conform if you can use in combination with made BRIDE.
Please feel free to contact us so we will also sell BRIDE seat rail.

Note: If you are attached to the S2000 has a case where BOX lid portion that housed the trunk opening and closing the switch can not be to interfere with the fully open to the sheet. In each case there is no problem if it is possible to slide the seat forward.

■ Specifications
Shell: FRP Silver Shell (VIOS3-based)
Skin fabric: Black & Red logo dedicated logo and dedicated Red stitch Add
Sheet weight about 7.1kg (not including the seat rails)

SEEKER SEATBELT WARNING CANCELER [ALUMINIUM]

Eliminates seatbelt warning light when using harness at the circuit / motorsport. Simply plug in to your stock seatbelt plug while you are not using the standard sash-belts.

SEEKER SUPER LOW-POSITION SEAT RAIL [RHS] JW5

Side is kept low position seat rail which corresponds to the full bucket seat of.
Since it is possible to adjust the front and rear, height, you can set the appropriate seat position in sports driving.

SEEKER SUPER LOW-POSITION SEAT RAIL [LHS] JW5

Side is kept low position seat rail which corresponds to the full bucket seat of.
Since it is possible to adjust the front and rear, height, you can set the appropriate seat position in sports driving.

SPOON SHIFT KNOB, ALUMINIUM [6MT] JW5

Spoon Alloy Shift Knob is the same countour as the Duracon however it is a little heavier at ~130g.
■ Includes 6MT Shift Patten Decal.
■ Includes Locking grub-screw and Allen wrench.
■ 10mm  / 1.5mm

SPOON SHIFT KNOB, DURACON [6MT] JW5

Spoon Duracon Shift Knob is made from a special Heat-Resistant Thermo-Plastic - perfect to resist heat-soak from the transmission and exhaust and heat from direct sunlight and Summer cabin temperatures. Lightweight design at just ~80g
■ Includes 6MT Shift Patten Decal.
■ Includes Locking grub-screw and Allen wrench.
■ 10mm  / 1.5mm

DURACON® is a crystalline thermoplastic acetal copolymer. The primary raw material trioxane, a trimer of formaldehyde.
The thermoplastic adopts a copolymer structure in which polyoxymethylene (-C-O) and carbon-carbon (-C-C- bond) comonomer groups are incorporated into its main chain. Therefore the copolymer has superior chemical and thermal stability, compared with acetal homopolymer. Acetal co-polymer is well-balanced in terms of mechanical, chemical and thermal properties, and its superior moldability allows it to be widely employed in various industrial fields.
Source: PolyPlastics.

SEEKER HEAVY SHIFT KNOB 400g [6MT] JW5

Same shape and size as Honda genuine shift knob - spherical type.
It was it possible to reliably shift work as well as to achieve a very moist and shift feel from its weight. Further, in order to perform a shift operation using the weight of 400g, it is gentle to be characterized for the respective gears.
We were greatly improved wear resistance and oxidation resistance subjected to TiAlN (titanium aluminum nitride coating) process on the surface. Furthermore SEEKER logo and shift patterns ( 6MT) to the top part we laser etching. Distinctive color and texture with the TiAlN, and enjoy the feel of heavyweight Come.
■ stainless steel surface treatment: TiAlN (titanium aluminum nitride coating). Weight: about 400g 5MT dedicated Honda genuine nuts separately if
■ genuine knob of car not a nut fixed You will need.

■ SEEKER: 400g (Stainless Steel)
■ STOCK: ~140g (Aluminium)