spoon OIL FILLER CAP

Extreme heat and engine vibration in Race Car can cause the OEM Plastic Cap to shake loose orSEEK even crack.
Spoon Oil Filler Cap made from High-Grade Aluminium, Expands at the same rate as your (Aluminium) Valve Cover, also has special rubber seal designed to reduce vibration transfer and hold cap in place.

seeker ULTRA-LIGHT OIL FILLER CAP [RED / BLUE / BLACK / GOLD / SILVER]

The aluminum oil filler cap is subjected to a lightening to the limit while sufficient strength has been achieved ultra-lightweight (individual weight ~60g). In addition, since we have adopted a good shape of Gakari finger is very easy to open and close the cap. One part of the vehicle such as FD2 you might shaft if fitted with a front tower bar outside is a difficult opening and closing of many filler cap those of layout through the just above the filler cap, but a round bar or the like to the filler cap lightening hole It can be relatively easily opened and closed by plug. Functional design that was obtained as a result of pursuing such utility is ideal for dress-up of the engine room.
WEIGHT: ~60g
AVAILABLE IN 5 COLOURS: ■Red ■Blue ■Black ■Gold ■Silver

SPOON RESERVOIR TANK COVER SET [SOX] *NEW*

The last thing you want to do at the circuit is lose traction thanks to someone having dropped fluids on to the track surface, let alone drop your own fluids and contribute to the problem - Spoon Reservoir Covers slide over your Brake Fluid Reservoir and Clutch Fluid Reservoir (etc.) and are designed to catch any fluids that may be spilled under high lateral-G driving at the circuit. Also helps prevent damage to engine-bay paintwork from spillage of Fluids.
25% Cotton 75% Polyester. 1PCE.

SEEKER RESERVOIR TANK COVER SET [SOX]

Fire Retardant Material. It is a safe reservoir tank cover that was manufactured in the flame-retardant material. Brake and clutch, and by using covered the reservoir tank of power steering fluid, to keep the quickly absorbed engine room boiling over of fluid to clean. The color is also the identity of the SEEKER "SEEKER orange".

SPOON HEAT BARRIER TAPE

Oil Viscosity decreases when subjected to constant high temperatures during performance driving. The Exhaust Manifold on B-series engines routes beneath the Oil Pan in very close proximity – this can lead to extreme heat transfer from the exhaust manifold. This is evident when you remove an old Oil Pan and inspect the shallow end of the pan where the exhaust manifold is closest – you will see baked on oil residue on the inside of the pan and this is clear evidence of high heat transfer from the exhaust. Spoon Heat Barrier Tape provides a thermal barrier in between the Exhaust Manifold and the Oil Pan. We recommend application of the Heat Barrier Tape to new Spoon Baffled Oil Pans as the fresh clean surface will provide excellent adhesion when the Oil Pan is new – plus installation Is very easy when the Oil Pan is off the engine. The Heat Barrier Tape can be used on other models and components where you would want to prevent heat transfer from various components into the fluid systems etc. For example Master Brake Cylinder (and Lines), Master Clutch Cylinder (and Lines) Brake Lines, S2000 Heat Shield… In fact, the Spoon S2000 Super Taikyu Race Car uses the heat shield over the entire Firewall through to the whole length of the Transmission Tunnel etc.
Size: 200mm x 300mm 

SPOON MAGNETIC DRAIN BOLT, ENGINE

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Engine Drain Bolt sold individually.

SPOON RADIATOR CAP [TYPE-D] FC2, FK7*

To raise the pressure of the cooling system raises the boiling point of the coolant. Spoon Radiator Caps raise the pressure to increase the efficiency of the cooling system. For the Complete Spoon Cooling System, we recomend using the Radiator Cap in combination withthe Spoon Thermo Switch, Spoon Thermostat and Spoon SEP Radiator Hoses. Please check with us for the correct type of Cap for use on your Vehicle - Type-D Caps suit newer Honda Radiators such as EG6/EG9/EG2/EK4/EK9/DC2/AP1/CL9 etc. Not suitable for use on Aftermarket radiators (please use Type-F).
SPOON: 1.35kgf/cm2
HONDA: 1.1kgf/cm2

SEEKER RADIATOR CAP [TYPE-D] FC2, FK7*

It is a high-pressure radiator cap to increase the pulling cooling efficiency boiling point of the coolant by increasing the pressure in the radiator.
This is quite useful at the time of high rotation traveling.
※ opening temperature: 1.3kgf / cm2 (normal 1.1)
1.3Kgf/cm2

SEEKER SUPREME EXHAUST SYSTEM [TAIL SILENCER] FK7 *COMING SOON*

Supreme Exhaust System for the 10th Generation Civic is under development.
PLEASE NOTE: Images are of Prototype exhaust - production verion may differ.
■ Dual exit layout.
■ Stainless Steel XXmm diameter piping (Catalyst-Back)
■ Blueprint Titanium finish 2-Tip Design specific to FK7 1.5 Turbo.
■ Db Rating to be announced.

SPOON MAGNETIC DRAIN BOLT, TRANSMISSION

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Transmission Drain Bolt sold individually.

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

SPOON CLUTCH SLAVE HOSE FK7 *NEW RELEASE*

■ Standard hydraullic lines use Rubber hose which is prone to flexing, ballooning and even splitting.
■ Spoon Clutch Slave Hose uses high-strength Stainless Steel Braided Hose that has also been internally Teflon Coated resulting in reliable clutch operation.
■ AVAILABLE NOW (JUNE 2018)

SPOON PROGRESSIVE SPRING FK7 *NEW RELEASE*

The biggest feature of the tenth generation Civic is compatibility of supple suspension feel and sporty handling performance, but in normal condition it is also where we want to stabilize the behavior a little more, such as roll and pitching. Therefore SPOON has developed a genuine shape spring with a normal ratio of about -30mm down and an increased spring rate by ~10%.
As the center of gravity lowers and the spring rate increases, the cornering performance improves dramatically, but since the thrust up feeling in the low speed range is set mildly, you can enjoy both winding and city riding.
■ Vehicle Ride height drop is FRONT -30mm, REAR -30mm
■ FRONT Spring Rate 2.7 kg/mm
■ REAR Spring Rate 3.2 kg/mm

SPOON SPRING RUBBER [S] FK8, FK7 *NEW RELEASE*

The Spoon Progressive Rate Springs have an initial (soft) spring rate and also the secondary (firm) spring rate. When the Coils are compressed and the force exceeds the initial spring rate, there may be some contact between the coils - this cans cause a slight noise in some instances. The Spoon Spring Rubber can be installed to reduce any noise you may encounter.

■ For use with Spoon Progressive Rate Springs (FK8/FK7) REAR
■ 2 PCE (for TWO Springs)
■ Recomended to install between the narrow part of the spring pitch to the wide part (as pictured)

6-POT FuLL-MONOCOQUE CALIPER SET FK7, FC2 *NEW*

Approximately one year has elapsed since the tenth generation Civic started to be released. SPOON has repeatedly tested every stage to pursue even higher ranking while taking advantage of the high total balance of Civic, but the most challenging in making a time attack on a circuit run was a car over 1300 kg It was an increase in brake burden due to heaviness. FK7 HATCHBACK / FC1 SEDAN's genuine brake disk size is Φ 282, 23 mm thick, but in the sports run the temperature of the brake disc exceeds 500°C, the same as the race. Therefore, at SPOON, we have newly developed for FK7 / FC1 based on the 6 POT monocoque calipers that had been testing and developing at Super Taikyu Series since 2016. The biggest feature of this "FULL Monoblock Caliper" is its capless design, developed without any compromise in all its structure, performance and durability.

■ Capless Full-Monocoque Body is manufactured with "Angle head processing machine". By adopting this construction method, it became possible to reduce the number of rubber parts, as a result the liquid loss was reduced.
■ The design of a caliper with high rigidity and light weight became possible. We adopted large diameter dust boots for ultra-thin piston and meet the required specifications even in street or circuit use.
■ Uneven Brake Pad wear was suppressed by optimizing Pad surface pressure by different diameter 6 PISTON design of Φ36 / Φ34 / Φ27.
■ 312mm diameter / 25 mm thick reversed ventilated disk is adopted to greatly suppress brake temperature rise and thermal collapse in sports driving. It also drastically improves the judder resistance and made it possible to sustain a stable brake feel even for continuous laps.
■ For the 6-POT CALIPER you must use SPOON BRAKE ROTOR [FRONT] FOR 6-POT [FK7 MT/CVT, FC1] 45251-FK7-000 (Φ312mm/25mm thickness) or compatible Rotor 294-320mm with Max thickness of 26mm.
■ For the 6-POT CALIPER you must use SPOON BRAKE PAD FRONT MB6 *STREET* 45022-MB6-S00 (Street Spec) or SPOON BRAKE PAD FRONT MB6 *CIRCUIT* 45022-MB6-C00

In addition, we pursued the optimal Front and Rear brake balance and also set the following rear pads so we recommend for simultaneous use with the Front 6-Pot Caliper package,.
■ SPOON BRAKE PAD REAR *STREET* [FK7 MT/CVT, FC1] 43022-FK7-S00 or SPOON BRAKE PAD REAR *CIRCUIT* [FK7 MT/CVT, FC1] 43022-FK7-C00

■ For Caliper clearance confirmation, Spoon has prepared a mounting pattern diagram / specification. Please cpontact Gaijin-Garage or CLICK HERE. Please see the blue dotted line part from the back side of the cut wheel. If the clearance of 2 mm or more can be confirmed with the red part and the wheel, that wheel can be mounted.
(RECOMMENDED ROTOR DIAMETER: 315mm, 25mm THICK)

■ COMPATIBLE ROTOR SIZE: Φ294-320mm / 25mm Thickness
■ AVAILABLE NOW (NOVEMBER 2018)

SPOON LONG HUB BOLT [EACH]

The standard Hub Bolts will only allow for use of a 5mm spacer maximum. Spoon Long Hub Bolts are +8mm longer than standard hub bolts to allow use of Wheel Spacers without compromise of the length of the thread the Wheel Nut has to bite. Recommended for use when installing Spoon Brake Calipers to enable use of Wheel Spacers to promote Caliper to Spoke clearance of Wheels.
Hub Bolt, Each.
SPOON: 52mm
HONDA: 44mm

SPOON LONG HUB BOLT [SET, 20]

The standard Hub Bolts will only allow for use of a 5mm spacer maximum. Spoon Long Hub Bolts are +8mm longer than standard hub bolts to allow use of Wheel Spacers without compromise of the length of the thread the Wheel Nut has to bite. Recommended for use when installing Spoon Brake Calipers to enable use of Wheel Spacers to promote Caliper to Spoke clearance of Wheels.
Hub Bolt, Set of 20.
SPOON: 52mm
HONDA: 44mm

SEEKER WIDE TREAD SPACER [5mm] EK9, EP3, FN2, FD2, DC2, DC5, AP1, AP2, ZF1

5mm Spacer 2PCE. 4x114 / 5x114. Aluminum is a die-cast of 5mm thickness wide tread spacer.
It was to minimize the camera shake by setting a high degree of accuracy and high strength and Honda vehicles only size the hub diameter (except one part of the model).
It will be the hub diameter 64m P.C.D 114.3 4 hole / 5 hole multi-type two 1SET.

BRAKE ROTOR, FRONT [FOR 6-POT CALIPER] FK7, FC2 *NEW*

SPOON BRAKE ROTOR FOR 6-POT CALIPERS (FK7/FC1) Approximately one year has elapsed since the tenth generation Civic started to be released. SPOON has repeatedly tested every stage to pursue even higher ranking while taking advantage of the high total balance of Civic, but the most challenging in making a time attack on a circuit run was a car over 1300 kg It was an increase in brake burden due to heaviness.
FK7 HATCHBACK / FC1 SEDAN's genuine brake disk size is Φ 282, 23mm thick, but in the sports run the temperature of the brake disc exceeds 500°C, the same as the race. Therefore, at SPOON, we have newly developed 6 POT monocoque calipers and special brake discs for FK7 / FC1 which had been testing and developing at Super Taikyu Series since 2016. Φ 312 By adopting a 25mm thick reversed ventilated disk, brake temperature rise and heat collapse are greatly suppressed in sports driving. It also greatly improves the judder resistance and realizes a stable brake feel even in continuous laps.

■ Specifically for use with 6-POT FULL MONOCOQUE CALIPER SET only.
■ ROTOR SIZE: 312mm Disk thickness: 25 mm
■ AVAILABLE NOW (NOVEMBER 2018)

BRAKE PAD, FRONT *STREET* [FOR 6-POT CALIPER] FK7, FC2 *NEW RELEASE*

This brake pad is designed exclusively for 6POT FULL MONOCOQUE CALIPER and adopts friction material mainly for Street.

■ Specifically for use with 6-POT FULL MONOCOQUE CALIPER SET only
■ For STREET / Sports use
■ TEMPERATURE RANGE 0 ~ 400℃
■ Not compatible with standard genuine Honda Caliper
■ AVAILABLE NOW (NOVEMBER 2018)

BRAKE PAD, FRONT *CIRCUIT* [FOR 6-POT CALIPER] FK7, FC2 *NEW RELEASE*

This brake pad is specially designed for 6 POT FULL MONOCOQUE CALIPER and adopts the corresponding friction material mainly at the Circuit.

■ Specifically for use with 6-POT FULL MONOCOQUE CALIPER SET only
■ For CIRCUIT / Race use
■ TEMPERATURE RANGE 0 ~ 600℃
■ Not compatible with standard genuine Honda Caliper
■ AVAILABLE NOW (NOVEMBER 2018)

SPOON BRAKE PAD, FRONT [STANDARD CALIPER] FK7, FC2 *NEW RELEASE*

Spoon Brake Pads are designed for performance use with improved pad-wear (and Rotor wear) at the Circuit and resistance to Fade under high-temperature use.
Recommended for Track use however can be used on Street by confident and competent drivers.
Operating Temperature Range: 0 ~400℃
Friction Coefficient: 0.32 to 0.38
Pad Material: Non-Asbestos-Based hardening type

SPOON BRAKE PAD, REAR [STANDARD CALIPER] FK7, FC2 *NEW RELEASE*

Spoon Brake Pads are designed for performance use with improved pad-wear (and Rotor wear) at the Circuit and resistance to Fade under high-temperature use.
Recommended for Track use however can be used on Street by confident and competent drivers.
Operating Temperature Range: 0 ~400℃
Friction Coefficient: 0.32 to 0.38
Pad Material: Non-Asbestos-Based hardening type

SPOON BRAKE HOSE SET FK7 *NEW RELEASE*

Spoon developed their high-strength Brake Hose Set to take the abuse of Circuit Use and Endurance Racing where the demands on the brake hydraullic system are extreme. Resistant to flex and heat, The Spoon Hoses will improve pedal feel and piston pressure and are an excellent upgrade for both Stock Brake Equipped vehicles an Big Brake Kits alike.
Spoon Brake Hose Set are made from high-strength Braided Stainless Steel Hose with inner Teflon coating for minimal resistance.

■ AVAILABLE NOW (JUNE 2018)

SPOON BRAKE PEDAL BOX FK8

Based on New Genuine Honda Brake Pedal Assembly, Spoon strengthens, boxes and re-inforces the arms to prevent any flex or fatigue through extreme motorsport use.
Dramatically improves the reliability of the brake control and promotes pedal stiffness.

SPOON CARBON BONNET FK7 *NEW RELEASE*

The biggest weak point of the tenth generation Civic is the weight of the car, especially the weight reduction of the front section not only alleviates the burden of braking but also the quick turning ability and the good handling characteristics indispensable for sports driving are demonstrated.
The characteristics of the successive SPOON carbon bonnet keeps the genuine body shape, the design is simple.
However, the calorific value of the turbo engine adopted from this tenth generation Civic was excessive, and it was necessary to reduce the heat inside the engine room as much as possible.
Therefore, the bonnet for FK7 is not only lightweight, but also has an air outlet inside the hood to finish it in a shape that allows the hot air in the engine room peculiar to the turbo engine to escape.
By providing an air outlet of the engine room, we will maximize the cooling performance of the radiator and intercooler.
■ STANDARD FK7 bonnet weight 14.5 kg
■ SPOON carbon bonnet was 7kg ~52% lighter than Standard.

SPOON ROOF SPOILER [FRP]FK7, FK8 *NEW RELEASE*

Spoon improved high speed stability by finishing the design that made use of the characteristic roof line and beautiful body form of the new 2017 Civic hatchback (FK7) and maximizing the rectifying effect.

■ Designed for FK7 but also fits Type R (FK8)
■ Wing is made from CARBON FIBRE
■ The mount part is FRP with white Gel-Coat

SPOON ROOF SPOILER [CARBON] FK7, FK8 *NEW RELEASE*

Spoon improved high speed stability by finishing the design that made use of the characteristic roof line and beautiful body form of the new 2017 Civic hatchback (FK7) and maximizing the rectifying effect.

■ Designed for FK7 but also fits Type R (FK8)
■ Wing is made from CARBON FIBRE
■ The mount part is FRP with white Gel-Coat

SEEKER SUPER WIDE BLUE MIRROR FK8, FK7, FC2, FC1 *NEW*

Seeker's Super Wide Blue Mirrors are handmade in Japan by the same manufacturer taht supplies to race categories such as Formula Dream, Formula Nippon and SUPER GT. 
■ The thickness is about 2 mm and a natural finish with no back-end feeling. While setting the bending angle to a level that does not greatly impair the distance feeling, realized a clear view with few blind spots.  It is easy to do garage parking and lane changes and contribute to safe driving.
■ The mirror is set to a sporty blue, greatly reduces dazzling during night driving by anti-glare processing water-repellent and hydrophilic coating.
■ Featuring the SEEKER logo on the Driver's side and the caution OBJECTS IN MIRROR ARE CLOSER THAN THEY APPEAR on the Passenger side. 
■ The color of the etched SEEKER logo / letters can be changed to white or black by using coloured tape or vinyl.

SW388 [18x8.5" +45 5H114.3] FC2, FC3, FK7, FN2, FD2, CL7 *NEW*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ 7.3KG Per Wheel
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint.
■ MADE IN JAPAN by Taneisya.
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight.
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improoves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts.
■ Centre cap is NOT included - sold separately 42703-CP01-BK.
■ Accepts Spoon 6-Piston Caliper without spacer.
■ 18”8.5J+45 5H114.3 Specifically for 10th Generation (2017-on) Civic 1.5T with 5x115.3 PCD.
■ AVAILABLE NOW (February 2018)

CENTER-CAP [SW388] ALL *NEW*

Spoon Sports Centre Cap for use with SW388 wheels.

■ Features Spoon Sports Logo.
■ Center Bore 67mm.

STICKER 01 / YELLOW [SPOKE DECAL FOR SW388] ALL *NEW*

Genuine Spoon Sports spoke decal (Yellow).

■ AVAILABLE NOW (November 2018)

SPOON CRO-MO WHEEL NUT M12 [BLACK] FK5, FK7, FC1, FC2*NEW RELEASE*

Spoon has developed new motorsport-spec CRO-MO WHEEL NUTS.
Of course they are Black to match your new SW388's, featuring the Spoon Logo and are now open-ended to suit extended Hub Bolts. Made in Japan from super-strong (yet lightweight) Chromium Molybdenum Steel, available in M12 x 1.5 pitch.

■ Set of 20 (20 PCE)
■ M12 x 1.5 pitch - perfect for Honda
■ 60° Taper / for Aftermarket Wheels
■ Released April 2019

SPOON BLUE WIDE REAR VIEW MIRROR FK8, FC2

Spoon Mirrors install over the existing standard mirror featuring 14000R Curvature for increased field of view with low-distortion - Basically the same field of view as a 'Broadway' mirror with just the small compact size of the standard mirror body.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.

SPOON STEERING WHEEL [340mm]

Spoon Steering Wheel is manufactured by Momo Italy utilising an unique rim contour and 340mmm diameter specifically designed for maximum grip under race conditions - especially suited for FF vehicles with extreme 'kick-back'. Covered in the highest quality Itallian leather with Red-stitching.
Includes Spoon Horn Button (not sold separately).

SEEKER RACING SPEC STEERING WHEEL [350mm] FK7 *COMING SOON*

Seeker Racing spec Steering Wheel for the 10th Generation Civic is under development. It is Kodawari of the steering wheel in pursuit of the sport driving, including race, and the like. 

PLEASE NOTE: Images are of PROTOTYPE product - production verion may differ.

■ 350mm diameter with thick rim contour for maxiumum grip.
■ Red-accent design to match Interior styling of Civic Type R FK8.
■ Frame made from high rigidity and a 6061 aluminum alloy
■ Luxurious perforated Leather
■ Red cross-stitching
■ 'R-SPIRIT' Horn Button included.
■ 'SEEKER' Logo embroidered at 6 o'clock.

SPOON STEERING BOSS [SRS DELETE] FC1/FC2, FK5/FK7, FK8

Spoon Steering Boss Kits are die-cast aluminium units designed for minimal weight and maximum strength.
Suitable for use with Spoon, Momo and Nardi wheels.
Includes SRS Delete Harness to eliminate the Airbag Warning Light.
Includes Steering Wheel Bolts (Allen style).

SPOON CARBON BUCKET SEAT [V2] *COMING SOON*

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.
■ Revised design to meet new Japanese safety standards (in development)
■ Pre-Orders JAN2019 - Production ETA April 2019

SPOON CARBON BUCKET SEAT [V1] *DISCONTINUED*

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.
■ Weight ~5.7Kg.
■ Discontinued 2018

SPOON ALUMINIuM SIDE STAY [FOR SPOON CARBON BUCKET SEAT]

Spoon Seat Bracket for use with Spoon Carbon Bucket Seats (Side-Mount).

■ Side-Mount Seat Bracket for use with Spoon Carbon Racing Bucket Seat.
■ For use with Seeker / Bride or Recaro Rails without side stay - for example Type-RO,RB. Drill Rail and fix with bolt.
■Includes Mounting hardware.

SEEKER x BRIDE FULL BUCKET SEAT [FRP]

It is a full bucket seat of the collaboration model of the BRIDE boasts a high rigidity and excellent hold of. The underlying shell has adopted the VIOS3 with the most matches easily seat position as much as possible down easy structure in Japanese type (Low MAX).
Shoulder support is somewhat smallish because, wearing indoor space to narrow a S2000 is also available.
This collaboration model inherits the design of the predecessor full bucket seat that had gotten popular, adopt a skin fabric red and black two-tone specification.
The BRIDE sheet somewhat strong competition image by the headrest further subjected to a dedicated logo embroidery to add a bright red stitch performance is intact, we have succeeded in that to be transformed into optimal fashionable to street youth It was.
BRIDE-made seat back protector in this product (black) is standard equipment.
Seat rail (sold separately) is a vehicle inspection also safe because it becomes a security standard conform if you can use in combination with made BRIDE.
Please feel free to contact us so we will also sell BRIDE seat rail.

Note: If you are attached to the S2000 has a case where BOX lid portion that housed the trunk opening and closing the switch can not be to interfere with the fully open to the sheet. In each case there is no problem if it is possible to slide the seat forward.

■ Specifications
Shell: FRP Silver Shell (VIOS3-based)
Skin fabric: Black & Red logo dedicated logo and dedicated Red stitch Add
Sheet weight about 7.1kg (not including the seat rails)

SEEKER SEATBELT WARNING CANCELER [ALUMINIUM]

Eliminates seatbelt warning light when using harness at the circuit / motorsport. Simply plug in to your stock seatbelt plug while you are not using the standard sash-belts.

SPOON SHIFT KNOB, ALUMINIUM [6MT]

Spoon Alloy Shift Knob is the same countour as the Duracon however it is a little heavier at ~130g.
Includes 6MT Shift Patten Decal.
Includes Locking grub-screw and Allen wrench.
10mm  / 1.5mm

SPOON SHIFT KNOB, DURACON [6MT]

Spoon Duracon Shift Knob is made from a special Heat-Resistant Thermo-Plastic - perfect to resist heat-soak from the transmission and exhaust and heat from direct sunlight and Summer cabin temperatures. Lightweight design at just ~80g
Includes 6MT Shift Patten Decal.
Includes Locking grub-screw and Allen wrench.
10mm  / 1.5mm

DURACON® is a crystalline thermoplastic acetal copolymer. The primary raw material trioxane, a trimer of formaldehyde.
The thermoplastic adopts a copolymer structure in which polyoxymethylene (-C-O) and carbon-carbon (-C-C- bond) comonomer groups are incorporated into its main chain. Therefore the copolymer has superior chemical and thermal stability, compared with acetal homopolymer. Acetal co-polymer is well-balanced in terms of mechanical, chemical and thermal properties, and its superior moldability allows it to be widely employed in various industrial fields.
Source: PolyPlastics.

SEEKER HEAVY SHIFT KNOB 400g [6MT] EP3, DC5, FN2, FD2, AP1, AP2, ZF1

Same shape and size as Honda genuine shift knob - spherical type.
It was it possible to reliably shift work as well as to achieve a very moist and shift feel from its weight. Further, in order to perform a shift operation using the weight of 400g, it is gentle to be characterized for the respective gears.
We were greatly improved wear resistance and oxidation resistance subjected to TiAlN (titanium aluminum nitride coating) process on the surface. Furthermore SEEKER logo and shift patterns ( 6MT) to the top part we laser etching. Distinctive color and texture with the TiAlN, and enjoy the feel of heavyweight Come. ■ stainless steel surface treatment: TiAlN (titanium aluminum nitride coating). Weight: about 400g 5MT dedicated Honda genuine nuts separately if ■ genuine knob of car not a nut fixed You will need.

SEEKER: 400g (Stainless Steel)
STOCK: ~140g (Aluminium)

SEEKER SHIFT BOOT COLLAR FN2, FD2, DC5, CL7, CL9, GE8, GK5, ZF1, FK2, FK8

Machined aluminium shift boot collar for use with aftermarket gearknobs on modern Hondas.

For CR-Z · S660 of GE-FIT and GK-FIT and 1 parts of which have taken a system that connects the shift boot and genuine knob, not good appearance when combined with external shift knob. This is especially recommended for the appropriate type of vehicle so you can improve the aesthetics in that you use this shift boot color.
In addition, since we have a standard feature an O-ring on the inside of the boot color, it is easily possible to set the vertical position of the color.
It also prevents abnormal noise which is generated by the vibration of the engine.

And removing the genuine color is easy mounting of only tighten this product with the supplied tie wrap.