SPOON ENGINE COMPLETE, K20A EP3

BORE x STROKE: XX.X mm × XX.Xmm (STOCK 86.0mm × 86.0mm)
COMPRESSION RATIO: 11.7
DISPLACEMENT: 1998cc
POWER: ~xxxPS@xxxx0RPM (STOCK 215PS@8000RPM)
TORQUE: ~xxxNm@xxxxRPM (STOCK 202Nm@7000RPM)
REV-LIMIT: x,xxxRPM (STOCK 8400RPM)
Specified engine oil: MOTUL 300V

Greatly imporved engine response / pickup through Spoon Balancing process.
Factory Tolerance 2.0g - Spoon Tolerance 0.02g.
Spoon Complete Engine based on Brand New Genuine Honda OEM Block and Head. All New Genuine Honda OEM Parts used in addition to:
- Spoon Head Gasket (+0.2:1 CR)
- Spoon Balanced Piston Set

Shipped in a Crate / Carton.

SPOON CARBON PLUG COVER [K20A] EP3

Ultra lightweight dry carbon ignition coil pack cover.


■ This item is on Backorder since ~2016

spoon OIL FILLER CAP

Extreme heat and engine vibration in Race Car can cause the OEM Plastic Cap to shake loose orSEEK even crack.
Spoon Oil Filler Cap made from High-Grade Aluminium, Expands at the same rate as your (Aluminium) Valve Cover, also has special rubber seal designed to reduce vibration transfer and hold cap in place.

seeker ULTRA-LIGHT OIL FILLER CAP [RED / BLUE / BLACK / GOLD / SILVER]

The aluminum oil filler cap is subjected to a lightening to the limit while sufficient strength has been achieved ultra-lightweight (individual weight ~60g). In addition, since we have adopted a good shape of Gakari finger is very easy to open and close the cap. One part of the vehicle such as FD2 you might shaft if fitted with a front tower bar outside is a difficult opening and closing of many filler cap those of layout through the just above the filler cap, but a round bar or the like to the filler cap lightening hole It can be relatively easily opened and closed by plug. Functional design that was obtained as a result of pursuing such utility is ideal for dress-up of the engine room.
WEIGHT: ~60g
AVAILABLE IN 5 COLOURS: ■Red ■Blue ■Black ■Gold ■Silver

SPOON YELLOW HEAD COVER [K20A] [EP3, DC5] EP3

Spoon Yellow Head Cover - Based on New Genuine Head Cover.
Includes Genuine Honda OEM Valve Cover Gasket Valve Cover Grommets and spark Plug Seals.

SPOON RACING PLUG # 24 [4PCE] EP3

For Circuit or Street use, Spoon Racing Plugs are optimesed for performance Honda engines.
As the Combusion Chamber heat value increases, the plugs have a better ability to cool down faster. (NGK8 number is equivalent.)

SPOON RESERVOIR TANK COVER SET [SOX] *NEW*

The last thing you want to do at the circuit is lose traction thanks to someone having dropped fluids on to the track surface, let alone drop your own fluids and contribute to the problem - Spoon Reservoir Covers slide over your Brake Fluid Reservoir and Clutch Fluid Reservoir (etc.) and are designed to catch any fluids that may be spilled under high lateral-G driving at the circuit. Also helps prevent damage to engine-bay paintwork from spillage of Fluids.
25% Cotton 75% Polyester. 1PCE.

SEEKER RESERVOIR TANK COVER SET [SOX]

Fire Retardant Material. It is a safe reservoir tank cover that was manufactured in the flame-retardant material. Brake and clutch, and by using covered the reservoir tank of power steering fluid, to keep the quickly absorbed engine room boiling over of fluid to clean. The color is also the identity of the SEEKER "SEEKER orange".

SPOON BAFFLE OIL PAN [K20A] EP3

Essential upgrade for ANY Circuit Use! Under high lateral G-force, through long sweeping corners at sustained high RPM, the Baffled Oil Pan helps prevent oil-starvation leading to catastrophic engine failure!
Spoon Baffled Oil Pan is based on a Brand New Genuine Honda OEM JDM Oil Pan with specially designed and manufactured Spoon Baffle Plates welded into place, re-powdercoated (on painted models) with Spoon Serial Number Plaque.
Includes Genuine Honda OEM Oil Pan Gasket (on models so required) and New Hamp Oil Filter.

SPOON HEAT BARRIER TAPE

Oil Viscosity decreases when subjected to constant high temperatures during performance driving. The Exhaust Manifold on B-series engines routes beneath the Oil Pan in very close proximity – this can lead to extreme heat transfer from the exhaust manifold. This is evident when you remove an old Oil Pan and inspect the shallow end of the pan where the exhaust manifold is closest – you will see baked on oil residue on the inside of the pan and this is clear evidence of high heat transfer from the exhaust. Spoon Heat Barrier Tape provides a thermal barrier in between the Exhaust Manifold and the Oil Pan. We recommend application of the Heat Barrier Tape to new Spoon Baffled Oil Pans as the fresh clean surface will provide excellent adhesion when the Oil Pan is new – plus installation Is very easy when the Oil Pan is off the engine. The Heat Barrier Tape can be used on other models and components where you would want to prevent heat transfer from various components into the fluid systems etc. For example Master Brake Cylinder (and Lines), Master Clutch Cylinder (and Lines) Brake Lines, S2000 Heat Shield… In fact, the Spoon S2000 Super Taikyu Race Car uses the heat shield over the entire Firewall through to the whole length of the Transmission Tunnel etc.
Size: 200mm x 300mm 

SPOON MAGNETIC DRAIN BOLT, ENGINE

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Engine Drain Bolt sold individually.

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

SPOON 2P HEAD GASKET [K20A] EP3

Weld-Type 2-Ply Head Gasket, super-strong bond design, improves torque through increased Compression.Ratio 0.2:1.
SPOON 0.45mm（STANDARD 0.75mm)
http://www.spoonsports.jp/philosophy04.html

SPOON PISTON, PISTON RING SET [OS] [K20A] EP3 DISCONTINUED

This kit has been in four sets and piston ring of 0.25mm over bore size for mass production. Weight of the piston within 1g, ring is located by aligning 0.07mm within the intersection of the abutment.

SPOON POLISH VALVE SET [K20A] EP3 *DISCONTINUED*

OEM 166.0g SPOON 163.4g

SPOON VALVE SPRING SET [K20A] EP3 *DISCONTINUED*

OEM 186.3g SPOON 148.4g

SPOON RADIATOR CAP [TYPE-D] EP3

To raise the pressure of the cooling system raises the boiling point of the coolant. Spoon Radiator Caps raise the pressure to increase the efficiency of the cooling system. For the Complete Spoon Cooling System, we recomend using the Radiator Cap in combination withthe Spoon Thermo Switch, Spoon Thermostat and Spoon SEP Radiator Hoses. Please check with us for the correct type of Cap for use on your Vehicle - Type-D Caps suit newer Honda Radiators such as EG6/EG9/EG2/EK4/EK9/DC2/AP1/CL9 etc. Not suitable for use on Aftermarket radiators (please use Type-F).
SPOON: 1.35kgf/cm2
HONDA: 1.1kgf/cm2

SPOON RADIATOR CAP [TYPE-F] AFTERMARKET RADIATORS

To raise the pressure of the cooling system raises the boiling point of the coolant. Spoon Radiator Caps raise the pressure to increase the efficiency of the cooling system. For the Complete Spoon Cooling System, we recomend using the Radiator Cap in combination withthe Spoon Thermo Switch, Spoon Thermostat and Spoon SEP Radiator Hoses. Please check with us for the correct type of Cap for use on your Vehicle - Type-F Caps suit older Honda Radiators such as EF9/EF8/DA9 etc. Also suitable for use on most aftermarket radiators such as Spoon, Koyo, Mishimoto etc.
SPOON: 1.35kgf/cm2
HONDA: 1.1kgf/cm2

SEEKER RADIATOR CAP [TYPE-D] EP3

It is a high-pressure radiator cap to increase the pulling cooling efficiency boiling point of the coolant by increasing the pressure in the radiator.
This is quite useful at the time of high rotation traveling.
※ opening temperature: 1.3kgf / cm2 (normal 1.1)
1.3Kgf/cm2

SEEKER RADIATOR CAP [TYPE-F]

It is a high-pressure radiator cap to increase the pulling cooling efficiency boiling point of the coolant by increasing the pressure in the radiator.
This is quite useful at the time of high rotation traveling.
※ opening temperature: 1.3kgf / cm2 (normal 1.1)
1.3Kgf/cm2

SPOON THERMO SWITCH EP3

Spoon Thermo Switch lowers the activation point of the Cooling Fan by ~13℃ over the OEM Thermo Switch to resist heat exchange.
Sub-zero / Extreme Winter conditions may require block-plate on Radiator to reach operating temperature.
OEM Thermo Swith activates at 93 ℃
SPOON Thermo Swith activates at 80 ℃

SPOON THERMOSTAT [K20A] EP3

Spoon Thermostat lowers the actuation point by ~10℃ over the OEM thermostat to resist heat exchange.
Sub-zero / Extreme Winter conditions may require block-plate on Radiator to reach operating temperature.
OEM Thermostat opens at 78 ℃ fully open 90 ℃
SPOON Thermostat opens at 70 ℃ fully open 82 ℃

SPOON SEP RADIATOR HOSE [K20A] EP3

Sports driving conditions with sharp rise and fall in engine speed, the radiator hoses can collapse under the engine movement and jolt in suction pressure, especially with oversized radiators and higher coolant vollumes.
The Spoon SEP material (Silicone-Modified Heat-Resistant Rubber) is heat-resistant 160 ℃ (Stock Ethylene-Propylene Rubber heat-resistant 120 ℃) is designed to be much stronger and more rigid than standard hoses.

When using Spoon Radiator Cap running higher pressure benefits in a higher boiling point so it is recommended to use the Spoon SEP Radiator Hoses in combination to worh with the rise in pressure from the Radiator Cap - for optimal cooling effect we recommend use with the Spoon Thermstat and Spoon Thermo Switch as a complete cooling system.

SPOON RACING COMPUTER [NTS EXCHANGE SERVICE] EP3 *DISCONTINUED*

From consideration fuel consumption, noise, exhaust gas, to aging, such as data such as ignition timing and air-fuel ratio of normal computer, has become a setting that gives satisfaction easy to get to everyone. The spoon, developed under a variety of conditions in order to meet higher output in the driving scene racing like more, the demand for high-response, to conduct the test, a safe total injection quantity of fuel, exhaust gas temperature, and ignition timing We are developing a computer while set in the area, to achieve high power. In addition, it would be a valley of torque inertia of the intake does not work is exposed mushroom type air cleaner box is required in the intake system at any STD even with a spoon made computer. On the other hand there is no problem if there is a flow rate ensure genuine equal to or greater than the exhaust system. However, please note, such as large-diameter pipe muffler can not expect an effect. We will respond to individual requests if you use in motor sports vehicles and on subjected to high-level tuning. Please contact motorsport Gr.

SPOON Earth Code EP3 *DISCONTINUED*

SEEKER ENGINE TORQUE DAMPER [SEEKER] EP3

Seeker Engine Torque Damper reduces shock transfer from hard shifting at high RPM. Also strengthens engine mounts. Features Damper Pre-Load adjustment.
Available for specific chassis, image is of EG/DC/EK style kit.
This item is identical to the Spoon engine torque damper that is discontinued.

SPOON ENGINE TORQUE DAMPER [SPOON] EP3 *DISCONTINUED*

SPOON VENTULI BIG THROTTLE BODY [K20A] EP3

Based on Brand New Gebuine Honda OEM JDM Throttle Body Assembly..
To maximise N/A Engine Power you must maximise the airflow into the intake chamber.
Spoon Venturi Big Throttle Body designed for optimal air flow and velocity utilizing the Stock Throttle body Casting. Diamond-Cut machining process with mirror-finish polished surface. Venturi effect funnel and large-diameter butterfly with eliptical cross-setion butterfly.
BUTTERFLY DIAMETER SPOON 65mm (STOCK 62mm)
OUTER DIAMETER SPOON 70mm (STOCK 62mm)
TB Gasket included on models so equipped.
Because you may be stepped with the intake manifold occurs depending on the model, it is recommended that you do at the same time processing of the intake manifold side.

SPOON VENTULI BIG THROTTLE BODY [NTS] EP3

[NTS] Exchange Service - Ship your ECU to Spoon Japan for work to be performed.
To maximise N/A Engine Power you must maximise the airflow into the intake chamber.
Spoon Venturi Big Throttle Body designed for optimal air flow and velocity utilizing the Stock Throttle body Casting. Diamond-Cut machining process with mirror-finish polished surface. Venturi effect funnel and large-diameter butterfly with eliptical cross-setion butterfly.
BUTTERFLY DIAMETER SPOON 65mm (STOCK 62mm)
OUTER DIAMETER SPOON 70mm (STOCK 62mm)
TB Gasket included on models so equipped.
Because you may be stepped with the intake manifold occurs depending on the model, it is recommended that you do at the same time processing of the intake manifold side.

SPOON AIR CLEANER [K20A] EP3

Spoon Air Filters are made from Microfibre material for far superior fine-particulate filtration and long-life. Maximum airflow / Minimum resistance will increase throttle response, torque and output.
Reduced inhalation resistance of 20% without impairing the dustproof effect by using a special Microfibre material with directivity. Designed to go inside of the Stock OEM Arbox for the best source of cool-air shielded from the engine bay heat for maximm torque.
Please note these filters are designed to be replaced rather than serviced.

SPOON 4-2 EXHAUST MANIFOLD EP3

Honda NA engine can be said that the advantages of 4-2-1 layout and high low-speed torque is relatively small. You can recommend testing, and experience be a combination of genuine and 2in1 exhaust manifold for that. Spoon made exhaust manifold of all, adopt the Tig welding method of clever technology and assembly Foul insert method there is no step between the port. I will give and also contributes to excellent handling by the nose is light, also a side effect. 3.2kg（ Std 5.8kg ）

SPOON 2-1 EXHAUST MANIFOLD EP3

And to exchange 2in1 genuine part for a wide torque band internal structure of the 2in1 part genuine skillful does not make sense in the running of the principal street in the practical range. This 2in1 exhaust manifold is granted benefits only be replaced if regular rotation range of the circuit is running high. Torque low-speed region's lost by replacing the exhaust manifold well, that the combination of characteristics that differ from mass production, selection of parts is the cause much so please be careful.

SPOON EXHAUST PIPE-B EP3

Spoon has layout to forward as much as possible the position of the main silencer of the exhaust pipe B first. As the exhaust gas temperature is high, the silencing effect is high, and is also contributes to the performance of the catalyst. By adopting the layout, the exhaust pressure is stabilized, the exhaust efficiency is enhanced. The exhaust system is an ideal that can be increased to ensure that power and torque with the lighter in combination with a spoon tail silencer. Because it is pure same standard flange, it is also possible combination of the original muffler.

SPOON N1 [TAIL SILENCER] EP3

It is the N1 type with an emphasis on sound quality Lacey and exciting feeling of power. It's to ensure sufficient flow rate, also volume flow rate of course. Because it is pure same standard flange, it is also possible combination of mass-produced intermediate pipe.

SPOON TAIL SILENCER [STREET] EP3 *DISCONTINUED*

It is a street type of sound quality and elegant torque characteristic emphasis. It's to ensure sufficient flow rate, also volume flow rate of course. Because it is pure same standard flange, it is also possible combination of mass-produced intermediate pipe.  90Db Weight: 7.0KG (STD 8.5KG) 0Db.

SPOON SUB SILENCER [65mm] EP3

Sub Silencer for use with 65mm tip N1 Systems. -5dB reduction.

*Does not fit FD2 N1 Tail Silencer, please use SPP-18030-020.

SPOON TRANSMISSION OVERHAUL [NTS EXCHANGE SERVICE] EP3

In a sense, it is difficult than the engine, the difference is easy to get to the life and shift feeling by hand feeling of kumite, but one person consistently mechanic of many years transmission dedicated decomposition the Company, washing, measuring, and reassembled I'm going is. The shift feel is smooth, from sense to put the gear, you will feel the transmission is going into nature. To motor sports Gr, please feel free to contact us consultation such as changing the gear ratio

SPOON MAGNETIC DRAIN BOLT, TRANSMISSION

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Transmission Drain Bolt sold individually.

SPOON MAGNETIC DRAIN BOLT SET [ENGINE + TRANSMISSION]

Microscopic metal fragments from the shearing of gears and wear of bearings etc. are collected by Spoon's high-power magnets.
Effectiveness of the product is immediately apparent after each oil change.
Set of Engine and Transmission Drain Bolts.

SEEKER LIGHT-WEIGHT FLYWHEEL [K20A] 3.8KG EP3

Result of extensive contemplation for balance of city riding and sports cars, we set the individual weight to the optimum 3.8kg. Very lightweight but high-strength, and I have been subjected to a dynamic balance, and promises a sharp racing from low rotation to high rotation. ※ genuine clutch system compliant products (please prepare a genuine pilot Bush during installation)

SPOON CLUTCH DISK [NON-ASBESTOS] EP3

Disc-Type Clutch for Street and sports Use. Rated for 500HP+
Can be used with Stock Clutch Cover. K20A

SPOON CLUTCH DISK [METAL] EP3

Puck-Type Clutch for Race Use - Not recommended for Street Use. Rated for 500HP+
Can be used with Stock Clutch Cover. K20A

SPOON CLUTCH COVER [PRESSURE PLATE] EP3

30% Higher crimp force without any increased pedal effort - Smooth operation and increased longevity. Resistant to judder sensation. K20A

SPOON RELEASE BEARING [SPOON] EP3

Spoon Release Bearings are hand-modified for reduced friction to ensure maximum performance and reliability under Race Conditions. K20A

SPOON CLUTCH SLAVE HOSE EP3

Standard hydraullic lines use Rubber hose which is prone to flexing, ballooning and even splitting. Spoon Clutch Slave Hose uses high-strength Stainless Steel Braided Hose that has also been internally Teflon Coated resulting in reliable clutch operation.

SPOON CROSS GEAR SET EP3, DC5 *DISCONTINUED*

SPOON 5th: 1.027 (STD 5th: 0.972)
SPOON 6th: 0.921 (STD 6th: 0.780)

■ DISCONTINUED ~2018

SPOON LSD KIT EP3

SPOON 1.5 Way Mechanical LSD for Competition Use.
Fully Servicable With Clutch Pack Set and Complete LSD Overhaul Sets available separately.
Initial torque setting set to 9 ~ 9.5kg (cold). Mechanical L. S. D. Structure, may the sound of the internal gear and sound dragging of the drive wheels, sound vibration occurs.
Genuine Honda OEM Side Bearing Included.

SPOON LSD CLUTCH PLATE SET EP3

LSD Clutch Plates are a consumable part, designed to wear over time. Replace yours with the Replacment Clutch Plate Set.

SPOON LSD OVERHAUL SET EP3

LSD Complete Overhaul Set - No need to replace your worn LSD - Rebuild it !

SPOON FINAL GEAR SET 5.1 EP3

5.062 FD. By replacing the final gear, it is valid, such as circuit racing can low gear of the final drive ratio.

SPOON FINAL GEAR SET 5.3 EP3

5.333 FD. By replacing the final gear, it is valid, such as circuit racing can low gear of the final drive ratio.

SEEKER HYPER GEAR ADVANCE, OIL [75W90] 1L

HYPER GEAR ADVANCE is a 100% chemical synthesis and the next generation oil embodying the mission oil to the ideal of SEEKER. Previously from HONDA sports car can be recommended finally with confidence repeat the development and testing on the target gear oil is we finished. Exchanges in the oil manufacturers and densely SEEKER reliable as background, has led to the completion by the "test-and-error" that repeats the harsh test of under all conditions. Because the original oil by our company which is specialized to HONDA cars we are proud to be the result obtained form what. If it is possible once the trial will be surprised to smooth shift feel from the cold up to the time of high temperature and high load.
■ HYPER GEAR features of ADVANCE very good
■ low-temperature fluidity, smooth shift feel realized from the cold shift feel the change even in high temperature and high load in
■ circuit driving, etc. will surely protect the gear at minimum.
■ easy-to-use 1L bottle.
■ genuine def we will of course respond to a mechanical LSD. ※ In the case of carbon LSD, etc. equipped car, please check with the manufacturer.
■ You can use it in any MT vehicles regardless of the drive system.
SPEC ￭ 100 Pasento SYNTHETIC SAE 75W-90 API GL-5 1L bottle.

SPOON DRIVE SHAFT SET EP3

Spoon Driveshafts are developed to have minimal frictional values to increase reliability of hte joints and shaft through endurance racing. With paired and balanced shafts and hand-polished joints to a mirror-finish, the result is greatly reduce surface fatique.
Based on NEW Genuine Honda Driveshafts.

SPOON DRIVE SHAFT SET [Air Vent, Special Grease] EP3

Spoon Driveshafts are developed to have minimal frictional values to increase reliability of hte joints and shaft through endurance racing. With paired and balanced shafts and hand-polished joints to a mirror-finish, the result is greatly reduce surface fatique.
Based on NEW Genuine Honda Driveshafts.

SPOON STRUT TOWER BAR, FRONT EP3 *DISCONTINUED*

Including the improvement in driving stability, letting up the rigidity of the car, giving the benefit of countless. Because of this rigidity, spoon commercialized tower bar. In front, to prevent distortion of the body by joining the left and right damper top of the engine room, to achieve certainty of handling by rigidity, maneuverability more direct. It is OK installation is simple, just shifted a little air conditioning hose.

SPOON STRUT TOWER BAR KIT EP3 *DISCONTINUED*

1m Oil-Resistant Hose for Brake Reservoir Relocation.

SPOON STRUT TOWER BAR [REAR] EP3 *DISCONTINUED*

creak of the body by A also increase the rigidity joined to the left and right top of the damper in the trunk, to reduce the deflection. Maneuverability changes to oversteer slightly. There is a need to process a little, such as the lining cutter If you are installing.

SPOON LOWER ARM BAR [FRONT] EP3 *DISCONTINUED*

SPOON LOWER ARM BAR [REAR] EP3 *DISCONTINUED*

SPOON PROGRESSIVE SPRING EP3 *DISCONTINUED*

Spoon Progressive Rate Springs improve the handling of your vehicle under sports driving condirions without any sacrifice to comfort for daily driving road conditions - The initial rate of the springs is similar to the (soft) stock springs to soak up the bumps and jolts experienced when driving over a poor quality surface. The Secondary spring rate is quite firm and kicks in under increased suspension load - giving an actual improvement to handing and performance with reduced body roll etc.
Spoon Progressive Rate Springs can be used with your stock Shocks/Dampers however for the best results, we recommend the springs are used in combination with the Spoon Fixed Dampers - the ultimate package for Sports Driving and Road Use.

SPOON: FRONT: 6.3 kg/mm REAR: 3.9 kg/mm
STOCK: FRONT: 6.2 kg/mm REAR: 2.8 kg/mm
-40mm Ride Height over Stock.

RIGID COLLAR [FRONT] EP3

8 PCE

RIGID COLLAR [REAR] EP3

12 PCE

SPOON MONOCOQUE CALIPER SET EP3

Spoon Monocoque Caliper features extremely high rigidity through the high-strength integrated monocoque design and cast alloy process.
Utilizing S2000 sized pads, there is a huge range of pad selection and availability and the 4-Piston design extends pad-life through the promotion of even Piston-to-Pad pressure. 100% compatible with ABS System and rear brake distribution.
Requires use of 300mm Brake Rotor with Maximum Rotor Thickness of 26mm.
SPOON MONOCOQUE CALIPER: 2.6Kg
S2000 STANDARD CALIPER: 4.7Kg
Piston size: 40.46φ + 36.12φ
Stock Pad Equivalent: 45022-AP1-000

PLEASE NOTE: When bleeding calipers, please do not over-tighten the bleed nipples – Specified Torque Value is 7.0Nm.
PLEASE NOTE: Caliper Clearance of various wheel combinations may require use of a Wheel Spacer – We recommend use of Spoon Extended Hub Bolts if you intend to run spacers. For Example: S2000 Genuine 16” (BBS) requires 15mm Wheel Spacer; CL7 Genuine Wheel required 5mm Wheel Spacer.

CALIPER REBUILD PARTS MONOCOQUE

Spoon Monocoque Calipers are designed for motorsport use and therefore have a full complimnet of spare and replacement parts available for pit-repairs or complete rebuild /overhaul.

SPOON LONG HUB BOLT [EACH]

The standard Hub Bolts will only allow for use of a 5mm spacer maximum. Spoon Long Hub Bolts are +8mm longer than standard hub bolts to allow use of Wheel Spacers without compromise of the length of the thread the Wheel Nut has to bite. Recommended for use when installing Spoon Brake Calipers to enable use of Wheel Spacers to promote Caliper to Spoke clearance of Wheels.
Hub Bolt, Each.
SPOON: 52mm
HONDA: 44mm

SPOON LONG HUB BOLT [SET, 20]

The standard Hub Bolts will only allow for use of a 5mm spacer maximum. Spoon Long Hub Bolts are +8mm longer than standard hub bolts to allow use of Wheel Spacers without compromise of the length of the thread the Wheel Nut has to bite. Recommended for use when installing Spoon Brake Calipers to enable use of Wheel Spacers to promote Caliper to Spoke clearance of Wheels.
Hub Bolt, Set of 20.
SPOON: 52mm
HONDA: 44mm

SPOON CRO-MO WHEEL NUT M12 [BLACK] EP3*NEW RELEASE*

Spoon has developed new motorsport-spec CRO-MO WHEEL NUTS.
Of course they are Black to match your new SW388's, featuring the Spoon Logo and are now open-ended to suit extended Hub Bolts. Made in Japan from super-strong (yet lightweight) Chromium Molybdenum Steel, available in M12 x 1.5 pitch.

■ Set of 20 (20 PCE)
■ M12 x 1.5 pitch - perfect for Honda
■ 60° Taper / for Aftermarket Wheels
■ Released April 2019

SEEKER WIDE TREAD SPACER [5mm] EP3

5mm Spacer 2PCE. 4x114 / 5x114. Aluminum is a die-cast of 5mm thickness wide tread spacer.
It was to minimize the camera shake by setting a high degree of accuracy and high strength and Honda vehicles only size the hub diameter (except one part of the model).
It will be the hub diameter 64m P.C.D 114.3 4 hole / 5 hole multi-type two 1SET.

SEEKER HIGH-CARBON ROTOR, SLOTTED [FRONT] EP3

Seeker high-carbon rotors have 20% increase in carbon content over standard rotors with significantly inclreased bite of the pads.
Features slotted design for performance use.

Pricing is for a pair of Rotors (RHS + LHS).

SEEKER HIGH-CARBON ROTOR [FRONT] EP3

Seeker high-carbon rotors have 20% increase in carbon content over standard rotors with significantly inclreased bite of the pads.

Pricing is for a pair of Rotors (RHS + LHS).

SPOON BRAKE PAD [FRONT] MONOBLOCK CALIPER

Spoon Brake Pads are designed for performance use with improved pad-wear (and Rotor wear) at the Circuit and resistance to Fade under high-temperature use.
Recommended for Track use however can be used on Street by confident and competent drivers.
Operating Temperature Range: 0 ~ 400 ℃
Friction Coefficient: 0.32 to 0.38
Pad Material: Non-Asbestos-Based hardening type

SPOON BRAKE PAD [REAR] EP3

Spoon Brake Pads are designed for performance use with improved pad-wear (and Rotor wear) at the Circuit and resistance to Fade under high-temperature use.
Recommended for Track use however can be used on Street by confident and competent drivers.
Operating Temperature Range: 0 ~ 400 ℃
Friction Coefficient: 0.32 to 0.38
Pad Material: Non-Asbestos-Based hardening type

SEEKER BRAKE PAD - TYPE C [FRONT] EP3

Seeker Type C Brake Pads are a high-performance pad tested in circuit racing conditions.
Carbon-Metal compound provides excellent braking force and resistance to fade with high durability and abrasion resistance. Can be used on the street by confident drivers.

Recommended for Circuit Use, Operating Temperature 0℃ ～ 700 ℃

SEEKER BRAKE PAD - TYPE C [REAR] EP3

Seeker Type C Brake Pads are a high-performance pad tested in circuit racing conditions.
Carbon-Metal compound provides excellent braking force and resistance to fade with high durability and abrasion resistance. Can be used on the street by confident drivers.

Recommended for Circuit Use, Operating Temperature 0℃ ～ 700 ℃

SW388 [16X7.5" +30 5X114.3] EK9, DC2, DC5, EP3 *NEW RELEASE*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ ~X.XKG Per Wheel (TO BE CONFIRMED)
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint
■ MADE IN JAPAN by Taneisya
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts
■ Centre cap sold separately
■ Clears Spoon Twin-Block Calipers without need for Spacer !
■ PRE-ORDERS NOW (ETA Late September 2019)

SW388 [18x8.5" +45 5H114.3] FC2, FC3, FK7, FN2, FD2, CL7 *NEW*

Spoon began development of the World's lightest aluminium wheel in partnership with Desmond Corporation in 1994. After 2 years of development to achieve the weight of 3.88KG per 15" Wheel, the original SW 388 was released in 1996. Production ended in 1999 with the closing of the Russion Press Factory.
Due to popular demand from our Customers, Spoon has now developed a revised wheel taking into consideration strength, weight, caliper clearance and modern sizes/specs. Spoon worked from the original drawings and designer of the SW388 from 1994, keeping the style of the original wheels combined with modern manufacturing processes and higher-grade materials to bring you a wheel that is superior.

■ 7.3KG Per Wheel
■ ANTHROCITE BLACK (Anodized Matte Black) the traditional Spoon finish is ligther and stronger than Paint.
■ MADE IN JAPAN by Taneisya.
■ Manufactured by Forge Cutting Method for maximum strength and minimum weight.
■ Contoured Hub-Face - Grooves cut on mounting face of the wheel provides natural even load dispersion to the hub, and improoves the fastening strength to the Wheel. This reduces the burden of shock absorption through the hub and knuckles. By being pulled outwards, the accuracy of the central axis after installation is increased. Also designed to prevent loosening of the hub-Bolts.
■ Centre cap is NOT included - sold separately 42703-CP01-BK.
■ Accepts Spoon 6-Piston Caliper without spacer.
■ 18”8.5J+45 5H114.3 Specifically for 10th Generation (2017-on) Civic 1.5T with 5x115.3 PCD.
■ AVAILABLE NOW (February 2018)

CENTER-CAP [SW388] ALL *NEW*

Spoon Sports Centre Cap for use with SW388 wheels.

■ Features Spoon Sports Logo.
■ Center Bore 67mm.
■ AVAILABLE NOW (February 2018)

STICKER 01 / YELLOW [SPOKE DECAL FOR SW388] ALL *NEW*

Genuine Spoon Sports spoke decal (Yellow).

■ AVAILABLE NOW (November 2018)

SPOON CRO-MO WHEEL NUT M12 [BLACK] EP3*NEW RELEASE*

Spoon has developed new motorsport-spec CRO-MO WHEEL NUTS.
Of course they are Black to match your new SW388's, featuring the Spoon Logo and are now open-ended to suit extended Hub Bolts. Made in Japan from super-strong (yet lightweight) Chromium Molybdenum Steel, available in M12 x 1.5 pitch.

■ Set of 20 (20 PCE)
■ M12 x 1.5 pitch - perfect for Honda
■ 60° Taper / for Aftermarket Wheels
■ Released April 2019

SPOON BLUE WIDE DOOR MIRROR *NEW* EP3

Spoon Door Mirrors install over the existing standard wing mirrors - featuring 900R Curvature for increased field of view with low-distortion.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.

SPOON HYDRO-BLUE WIDE MIRROR EP3 *DISCONTINUED*

Spoon Mirrors install over the existing standard wing mirrors featuring 900R Curvature for increased field of view with low-distortion.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.
Hydrophilic Blue coating is also water and dirt resistant.

SPOON BLUE WIDE REAR VIEW MIRROR EP3

Spoon Mirrors install over the existing standard mirror featuring 14000R Curvature for increased field of view with low-distortion - Basically the same field of view as a 'Broadway' mirror with just the small compact size of the standard mirror body.
Titanium Oxide Optical Coating provides a photocatalytic effect to reduce glare / dazzling effect from the lights of other vehicles and reduce driver fatigue.

SPOON STEERING WHEEL [340mm]

Spoon Steering Wheel is manufactured by Momo Italy utilising an unique rim contour and 340mmm diameter specifically designed for maximum grip under race conditions - especially suited for FF vehicles with extreme 'kick-back'. Covered in the highest quality Itallian leather with Red-stitching.
Includes Spoon Horn Button (not sold separately).

SEEKER RACING SPEC STEERING WHEEL [325mm]

It is Kodawari of the steering wheel in pursuit of the sport driving, including race, and the like. 
The high rigidity and a 6061 aluminum alloy 5t with excellent corrosion resistance using the base frame epidermis was arrogance luxury smooth leather. (Using a punching leather to 9 o'clock, 3 o'clock in order to improve the familiar). Grip has adopted a finger Gakari good shape a slightly thick as can be driving and disconnect the power.  Stitch of the portion of force is applied does not have a worry that leather may come off even if I use it for many years I have been put in a cross-shaped. 
In addition to place a well-balanced logo and the top mark and our slogan to several places body finished in a stylish design. 
"R-SPIRIT" horn button of the dedicated will be attached. ■ specification steering outer diameter: 325mm Frame: 6061 aluminum alloy 5t Stitch: Red color of the cross-stitch epidermis: Luxury Black smooth leather (partially use the punching leather) Embroidery: Top on the surface 6 o'clock SEEKER logo, at 12 o'clock mark, embroidery our slogan on the back 12 o'clockhorn: dedicated "R-SPIRIT" horn button included

SPOON STEERING BOSS [SRS-DELETE] EP3

Spoon Steering Boss Kits are die-cast aluminium units designed for minimal weight and maximum strength.
Suitable for use with Spoon, Momo and Nardi wheels.
Includes SRS Delete Harness to eliminate the Airbag Warning Light.
Includes Steering Wheel Bolts (Allen style).

SPOON STEERING BOSS [SRS-DELETE] FD2, FN2, ZF1

Spoon Steering Boss Kits are die-cast aluminium units designed for minimal weight and maximum strength.
Suitable for use with Spoon, Momo and Nardi wheels.
Includes SRS Delete Harness to eliminate the Airbag Warning Light.
Includes Steering Wheel Bolts (Allen style).

SPOON CARBON BUCKET SEAT [V2] *COMING SOON*

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.
■ Revised design to meet new Japanese safety standards (in development)
■ Pre-Orders JAN2019 - Production ETA April 2019

SPOON CARBON BUCKET SEAT [V1] *DISCONTINUED*

Spoon Racing Carbon Bucket Seats are designed to hold the driver firmly into place in the perfect driving position. Ultra lightweight Carbon Fibre construction, weighing in at only 5.7Kg, this is the ultimate Racing Seat for your Honda. Designed to reduce driver-fatigue through long races.
■ Weight ~5.7Kg.
■ Discontinued 2018

SPOON ALUMINIuM SIDE STAY [FOR SPOON CARBON BUCKET SEAT]

Spoon Seat Bracket for use with Spoon Carbon Bucket Seats (Side-Mount).

■ Side-Mount Seat Bracket for use with Spoon Carbon Racing Bucket Seat.
■ For use with Seeker / Bride or Recaro Rails without side stay - for example Type-RO,RB. Drill Rail and fix with bolt.
■Includes Mounting hardware.

SEEKER x BRIDE FULL BUCKET SEAT [FRP]

It is a full bucket seat of the collaboration model of the BRIDE boasts a high rigidity and excellent hold of. The underlying shell has adopted the VIOS3 with the most matches easily seat position as much as possible down easy structure in Japanese type (Low MAX).
Shoulder support is somewhat smallish because, wearing indoor space to narrow a S2000 is also available.
This collaboration model inherits the design of the predecessor full bucket seat that had gotten popular, adopt a skin fabric red and black two-tone specification.
The BRIDE sheet somewhat strong competition image by the headrest further subjected to a dedicated logo embroidery to add a bright red stitch performance is intact, we have succeeded in that to be transformed into optimal fashionable to street youth It was.
BRIDE-made seat back protector in this product (black) is standard equipment.
Seat rail (sold separately) is a vehicle inspection also safe because it becomes a security standard conform if you can use in combination with made BRIDE.
Please feel free to contact us so we will also sell BRIDE seat rail.

Note: If you are attached to the S2000 has a case where BOX lid portion that housed the trunk opening and closing the switch can not be to interfere with the fully open to the sheet. In each case there is no problem if it is possible to slide the seat forward.

■ Specifications
Shell: FRP Silver Shell (VIOS3-based)
Skin fabric: Black & Red logo dedicated logo and dedicated Red stitch Add
Sheet weight about 7.1kg (not including the seat rails)

SEEKER SEATBELT WARNING CANCELER [ALUMINIUM]

Eliminates seatbelt warning light when using harness at the circuit / motorsport. Simply plug in to your stock seatbelt plug while you are not using the standard sash-belts.

SEEKER SUPER LOW-POSITION SEAT RAIL [RHS] EP3

Side is kept low position seat rail which corresponds to the full bucket seat of.
Since it is possible to adjust the front and rear, height, you can set the appropriate seat position in sports driving.

SEEKER SUPER LOW-POSITION SEAT RAIL [LHS] EP3

Side is kept low position seat rail which corresponds to the full bucket seat of.
Since it is possible to adjust the front and rear, height, you can set the appropriate seat position in sports driving.

SPOON LOW POSITION SEAT SLIDER [LHS] EP3 *DISCONTINUED*

This Spoon seat rail is lowered by 5cm and moves the seat closer to floor for an improved driving position and lower Centre of Gravity.

SPOON LOW POSITION SEAT SLIDER [RHS] EP3 *DISCONTINUED*

This Spoon seat rail is lowered by 5cm and moves the seat closer to floor for an improved driving position and lower Centre of Gravity.

SPOON SHIFT KNOB, ALUMINIUM [6MT]

Spoon Alloy Shift Knob is the same countour as the Duracon however it is a little heavier at ~130g.
Includes 6MT Shift Patten Decal.
Includes Locking grub-screw and Allen wrench.
10mm  / 1.5mm

SPOON SHIFT KNOB, DURACON [6MT]

Spoon Duracon Shift Knob is made from a special Heat-Resistant Thermo-Plastic - perfect to resist heat-soak from the transmission and exhaust and heat from direct sunlight and Summer cabin temperatures. Lightweight design at just ~80g
Includes 6MT Shift Patten Decal.
Includes Locking grub-screw and Allen wrench.
10mm  / 1.5mm

DURACON® is a crystalline thermoplastic acetal copolymer. The primary raw material trioxane, a trimer of formaldehyde.
The thermoplastic adopts a copolymer structure in which polyoxymethylene (-C-O) and carbon-carbon (-C-C- bond) comonomer groups are incorporated into its main chain. Therefore the copolymer has superior chemical and thermal stability, compared with acetal homopolymer. Acetal co-polymer is well-balanced in terms of mechanical, chemical and thermal properties, and its superior moldability allows it to be widely employed in various industrial fields.
Source: PolyPlastics.

SEEKER HEAVY SHIFT KNOB 400g [6MT] EP3, DC5, FN2, FD2, AP1, AP2, ZF1

Same shape and size as Honda genuine shift knob - spherical type.
It was it possible to reliably shift work as well as to achieve a very moist and shift feel from its weight. Further, in order to perform a shift operation using the weight of 400g, it is gentle to be characterized for the respective gears.
We were greatly improved wear resistance and oxidation resistance subjected to TiAlN (titanium aluminum nitride coating) process on the surface. Furthermore SEEKER logo and shift patterns ( 6MT) to the top part we laser etching. Distinctive color and texture with the TiAlN, and enjoy the feel of heavyweight Come. ■ stainless steel surface treatment: TiAlN (titanium aluminum nitride coating). Weight: about 400g 5MT dedicated Honda genuine nuts separately if ■ genuine knob of car not a nut fixed You will need.

SEEKER: 400g (Stainless Steel)
STOCK: ~140g (Aluminium)

SEEKER SHIFT BOOT COLLAR EP3

Machined aluminium shift boot collar for use with aftermarket gearknobs on modern Hondas.

For CR-Z · S660 of GE-FIT and GK-FIT and 1 parts of which have taken a system that connects the shift boot and genuine knob, not good appearance when combined with external shift knob. This is especially recommended for the appropriate type of vehicle so you can improve the aesthetics in that you use this shift boot color.
In addition, since we have a standard feature an O-ring on the inside of the boot color, it is easily possible to set the vertical position of the color.
It also prevents abnormal noise which is generated by the vibration of the engine.

And removing the genuine color is easy mounting of only tighten this product with the supplied tie wrap.

sEEKER SHIFT BOOT COLLAR [OEM NUT] EP3

Machined aluminium shift boot collar for use with aftermarket gearknobs on modern Hondas.

For CR-Z · S660 of GE-FIT and GK-FIT and 1 parts of which have taken a system that connects the shift boot and genuine knob, not good appearance when combined with external shift knob. This is especially recommended for the appropriate type of vehicle so you can improve the aesthetics in that you use this shift boot color.
In addition, since we have a standard feature an O-ring on the inside of the boot color, it is easily possible to set the vertical position of the color.
It also prevents abnormal noise which is generated by the vibration of the engine.

And removing the genuine color is easy mounting of only tighten this product with the supplied tie wrap.